#4-48 UNF tap drill size
Tap #4-48 UNF with a #42 drill (0.0935 in, 2.37 mm), about 68% thread. Taps this fine break easily, so hand-tap with cutting oil and back off often.
| Drill | inch | mm | Thread % | Typical use |
|---|---|---|---|---|
| #43 | 0.0890 | 2.26 | 85.0% | General purpose |
| 2.35 mm (metric drill) | 0.0925 | 2.35 | 72.0% | General purpose |
| #42 (chart drill) | 0.0935 | 2.37 | 68.4% | Hard or tough material, deep or blind holes |
| 3/32" | 0.0938 | 2.38 | 67.4% | Hard or tough material, deep or blind holes |
| #41 | 0.0960 | 2.44 | 59.1% | Low engagement: check strength |
| Thread | Tap drill | Tap drill (mm) | Clearance close / free |
|---|---|---|---|
| #2-64 UNF | #50 (0.0700 in) | 1.78 mm | #43 / #41 |
| #3-56 UNF | #45 (0.0820 in) | 2.08 mm | #37 / #35 |
| #4-48 UNF (this page) | #42 (0.0935 in) | 2.37 mm | #32 / #30 |
| #5-44 UNF | #37 (0.1040 in) | 2.64 mm | #30 / #29 |
| #6-40 UNF | #33 (0.1130 in) | 2.87 mm | #27 / #25 |
Practical notes
At 48 TPI the basic thread depth is only about 0.0113 in per side, so small errors in drill size change engagement a lot. Use a sharp, correctly sized drill, a tap guide to keep the tap square, and limit thread depth to about 1.5 × diameter.
Thread-forming taps are popular for #4 sizes in aluminium and brass because they make no chips; they need a larger hole, roughly 0.1016 in (2.58 mm, D − 0.5 × pitch). Confirm against the tap maker's chart.
If a #4 thread in plastic or a printed part must survive repeated assembly, a threaded insert is usually more durable than tapping the base material.
UNF (fine) threads have more threads per inch than UNC, a larger tensile stress area and better resistance to loosening, but they strip more easily in soft material and are more sensitive to drill size.
Clearance drills for a #4 screw: close fit #32 (0.1160 in, 2.95 mm), free fit #30 (0.1285 in, 3.26 mm).
FAQ
What size drill for a #4-48 UNF tap?
The standard tap drill for #4-48 UNF is a #42 drill, 0.0935 in (2.37 mm), which gives about 68% thread.
What clearance hole for a #4 UNF screw?
Use #32 (0.1160 in, 2.95 mm) for a close fit or #30 (0.1285 in, 3.26 mm) for a free fit. Clearance depends on diameter only, so it is the same for UNC and UNF #4 screws.
What metric drill can I use for #4-48 UNF?
The closest metric drill is 2.35 mm (0.0925 in), giving about 72% thread on #4-48 UNF.
What is the difference between #4-48 UNF and #4-40 UNC?
Both are #4 diameter. #4-48 UNF has 48 threads per inch and uses a #42 tap drill (0.0935 in); #4-40 UNC has 40 TPI and uses a #43 drill (0.0890 in). The threads are not interchangeable.
Sources: ASME B1.1 — Unified inch screw threads (UN and UNR form) · Machinery's Handbook — tap drill sizes and percentage-of-thread formula · ASME B94.11M — twist drills (number and letter drill sizes) · Common machinist clearance-drill chart (close / free fit)
Need it made?
Post the job free — verified makers quote you.
Post a CNC machining job Open the Tap & Drill Size Chart calculator