M14 x 1.5 tap drill size
Drill 12.5 mm for an M14 x 1.5 fine thread: the 14 mm major diameter minus the 1.5 mm pitch, giving about 77% thread.
| Drill | mm | inch | Thread % | Typical use |
|---|---|---|---|---|
| 12.3 mm | 12.3 | 0.4843 | 87.2% | Tight: high tapping torque, tap breakage risk |
| 31/64" (inch drill) | 12.3 | 0.4844 | 87.1% | Tight: high tapping torque, tap breakage risk |
| 12.4 mm | 12.4 | 0.4882 | 82.1% | General purpose |
| 12.5 mm (ISO 2306) | 12.5 | 0.4921 | 77.0% | General purpose |
| 12.6 mm | 12.6 | 0.4961 | 71.8% | General purpose |
| 12.7 mm | 12.7 | 0.5000 | 66.7% | Hard or tough material, deep or blind holes |
| Thread | Tap drill | Tap drill (in) | Clearance (ISO 273 medium) |
|---|---|---|---|
| M12 x 1.5 | 10.5 mm | 0.4134 in | 13.5 mm |
| M12 x 1.25 | 10.75 mm | 0.4232 in | 13.5 mm |
| M14 x 1.5 (this page) | 12.5 mm | 0.4921 in | 15.5 mm |
| M16 x 1.5 | 14.5 mm | 0.5709 in | 17.5 mm |
| M18 x 1.5 | 16.5 mm | 0.6496 in | 20.0 mm |
Practical notes
Drilling 12.5 mm in one pass puts a lot of load on the spindle and workholding. Pilot-drill first, then open up to size; an undersize hole is the most common cause of a seized or broken tap at this size.
Tapping torque rises steeply with diameter. On a machine use a tapping head or rigid tapping; for one-off or high-value parts, thread milling avoids the risk of a broken tap and lets you adjust the fit. Threads in tubes or bosses this size are often single-point cut on a lathe instead.
Typical engagement lengths: about 1 × diameter in steel, 1.5 × in cast iron or brass and 2 × in aluminium. In softer materials a longer engagement does more for strength than a tighter tap drill.
Large fine-pitch threads such as M14 x 1.5 are typical on shafts, bearing locknuts and thin-walled housings, where a coarse thread would cut too deep into the wall. The shallower thread makes drill size more critical: a 0.1 mm change shifts engagement by about 5 percentage points.
Clearance holes come from ISO 273: fine (close) 15.0 mm, medium (normal) 15.5 mm, coarse (loose) 16.5 mm. Use fine for location, medium as the default and coarse when hole positions vary.
FAQ
What size drill for an M14 x 1.5 tap?
Use a 12.5 mm drill (0.4921 in) for a cut M14 x 1.5 tap, per ISO 2306 (major diameter minus pitch). It gives about 77% thread.
What clearance hole for an M14 bolt?
ISO 273 gives 15.0 mm (fine/close), 15.5 mm (medium/normal) and 16.5 mm (coarse/loose) for M14, whatever the pitch. Medium is the usual default.
What inch drill can I use for an M14 x 1.5 tap?
The closest inch drill is 31/64" (0.4844 in, 12.3 mm), which gives about 87% thread on M14 x 1.5. That is noticeably different from the metric drill, so use it only if the metric size is unavailable.
How is M14 x 1.5 different from other M14 pitches?
Same 14 mm major diameter, different pitch, so a different tap drill: M14 x 2.0 (12.0 mm drill). The taps and bolts are not interchangeable with M14 x 1.5 (12.5 mm drill).
Sources: ISO 261 — ISO general purpose metric screw threads, general plan (pitches) · ISO 724 — basic dimensions (minor diameter D1 = D − 1.0825 P) · ISO 2306 — drills for use prior to tapping (tap drill = D − P) · ISO 273 — clearance holes for bolts and screws · Machinery's Handbook — percentage-of-thread formula
Need it made?
Post the job free — verified makers quote you.
Post a Metal fabrication job Open the Tap & Drill Size Chart calculator