#6-32 UNC tap drill size
Use a #36 drill (0.1065 in, 2.71 mm) for #6-32 UNC. It is the standard chart size and leaves about 78% thread, enough for full practical strength without excessive tapping torque.
| Drill | inch | mm | Thread % | Typical use |
|---|---|---|---|---|
| #37 | 0.1040 | 2.64 | 83.8% | General purpose |
| 2.7 mm (metric drill) | 0.1063 | 2.7 | 78.1% | General purpose |
| #36 (chart drill) | 0.1065 | 2.71 | 77.6% | General purpose |
| 7/64" | 0.1094 | 2.78 | 70.5% | General purpose |
| #35 | 0.1100 | 2.79 | 69.0% | Hard or tough material, deep or blind holes |
| #34 | 0.1110 | 2.82 | 66.5% | Hard or tough material, deep or blind holes |
| #33 | 0.1130 | 2.87 | 61.6% | Hard or tough material, deep or blind holes |
| Thread | Tap drill | Tap drill (mm) | Clearance close / free |
|---|---|---|---|
| #4-40 UNC | #43 (0.0890 in) | 2.26 mm | #32 / #30 |
| #5-40 UNC | #38 (0.1015 in) | 2.58 mm | #30 / #29 |
| #6-32 UNC (this page) | #36 (0.1065 in) | 2.71 mm | #27 / #25 |
| #8-32 UNC | #29 (0.1360 in) | 3.45 mm | #18 / #16 |
| #10-24 UNC | #25 (0.1495 in) | 3.8 mm | #9 / #7 |
Practical notes
Spiral-point taps suit through holes; spiral-flute taps lift chips out of blind holes. In a blind hole, drill a few threads deeper than the full-thread depth you need.
Typical engagement lengths: about 1 × diameter in steel, 1.5 × in cast iron or brass and 2 × in aluminium. In tough stainless or hardened steel a slightly larger drill (60–70% thread) cuts torque and tap breakage with little loss of strength.
Thread-forming (roll) taps need a larger hole, roughly 0.1224 in (3.11 mm, D − 0.5 × pitch). Check the tap maker's chart; forming suits ductile metals such as aluminium, mild steel and brass, not cast iron.
UNC (coarse) is the default Unified series: quicker to assemble, more tolerant of dirt and damage, and better in soft materials such as aluminium and cast iron.
Clearance drills for a #6 screw: close fit #27 (0.1440 in, 3.66 mm), free fit #25 (0.1495 in, 3.8 mm).
FAQ
What size drill for a #6-32 UNC tap?
The standard tap drill for #6-32 UNC is a #36 drill, 0.1065 in (2.71 mm), which gives about 78% thread.
What clearance hole for a #6 UNC screw?
Use #27 (0.1440 in, 3.66 mm) for a close fit or #25 (0.1495 in, 3.8 mm) for a free fit. Clearance depends on diameter only, so it is the same for UNC and UNF #6 screws.
What metric drill can I use for #6-32 UNC?
The closest metric drill is 2.7 mm (0.1063 in), giving about 78% thread on #6-32 UNC.
What is the difference between #6-32 UNC and #6-40 UNF?
Both are #6 diameter. #6-32 UNC has 32 threads per inch and uses a #36 tap drill (0.1065 in); #6-40 UNF has 40 TPI and uses a #33 drill (0.1130 in). The threads are not interchangeable.
Sources: ASME B1.1 — Unified inch screw threads (UN and UNR form) · Machinery's Handbook — tap drill sizes and percentage-of-thread formula · ASME B94.11M — twist drills (number and letter drill sizes) · Common machinist clearance-drill chart (close / free fit)
Need it made?
Post the job free — verified makers quote you.
Post a CNC machining job Open the Tap & Drill Size Chart calculator